Skip to main content
Top
Published in: Clinical Oral Investigations 7/2014

01-09-2014 | Original Article

Study of temperature variation in cortical bone during osteotomies with trephine drills

Authors: Sergio Alexandre Gehrke, Marcelo Khoury Pazetto, Sérgio de Oliveira, Stefano Corbella, Silvio Taschieri, Fábio E. C. Mardegan

Published in: Clinical Oral Investigations | Issue 7/2014

Login to get access

Abstract

Objective

The purpose of this study was to compare temperature variation during osteotomies with trephine drills under different irrigation conditions: without irrigation, external irrigation, and double irrigation.

Materials and methods

Synthetic blocks of bone (type I density) were used for drilling procedures with an experimental computed machine, which measured the maximum temperature in the cortical bone during osteotomy with a bone cut that was 5 mm in both diameter and depth. Three groups were formed depending on the irrigation conditions: no irrigation (G1), external irrigation (G2), and double irrigation (G3). Fifty drillings were performed for each group.

Results

The average thermal increase in the groups was 21.7 ± 1.52 °C in G1, 14.2 ± 0.70 °C in G2, and 12.4 ± 0.75 °C in G3. The results presented statistically significant differences among all groups (α = 0.05).

Conclusion

The double irrigation technique resulted in a smaller increase in temperature in the cortical bone model, demonstrating a greater efficiency, which may be beneficial when compared to external irrigation alone.

Clinical relevance

The trephine has been widely used in removing small blocks for bone graft, especially the posterior mandible, where the possibility of heating may be higher due to the density of cortical bone in this area. So it is important that the professionals select instruments that can reduce the risks of complications in the proposed treatment.
Literature
1.
go back to reference Tilotta F, Lazaroo B, Gaudy JF (2008) Gradual and safe technique for sinus floor elevation using trephines and osteotomes with stops: a cadaveric anatomic study. Oral Surg Oral Med Oral Pathol Oral Radiol Endod 106:210–216PubMedCrossRef Tilotta F, Lazaroo B, Gaudy JF (2008) Gradual and safe technique for sinus floor elevation using trephines and osteotomes with stops: a cadaveric anatomic study. Oral Surg Oral Med Oral Pathol Oral Radiol Endod 106:210–216PubMedCrossRef
2.
go back to reference Thuaksuban N, Nuntanaranont T, Pripatnanont P (2010) A comparison of autogenous bone graft combined with deproteinized bovine bone and autogenous bone graft alone for treatment of alveolar cleft. Int J Oral Maxillofac Surg 39(12):1175–1180PubMedCrossRef Thuaksuban N, Nuntanaranont T, Pripatnanont P (2010) A comparison of autogenous bone graft combined with deproteinized bovine bone and autogenous bone graft alone for treatment of alveolar cleft. Int J Oral Maxillofac Surg 39(12):1175–1180PubMedCrossRef
3.
go back to reference Stenport VF, Örtorp A, Thor A (2011) Onlay and inlay bone grafts with platelet-rich plasma: histologic evaluations from human biopsies. J Oral Maxillofac Surg 69(4):1079–1085PubMedCrossRef Stenport VF, Örtorp A, Thor A (2011) Onlay and inlay bone grafts with platelet-rich plasma: histologic evaluations from human biopsies. J Oral Maxillofac Surg 69(4):1079–1085PubMedCrossRef
4.
go back to reference Lundskog J (1972) Heat and bone tissue. An experimental investigation of the thermal properties of bone and threshold levels for thermal injury. Scand J Plast Reconstr Surg 9:1–80PubMed Lundskog J (1972) Heat and bone tissue. An experimental investigation of the thermal properties of bone and threshold levels for thermal injury. Scand J Plast Reconstr Surg 9:1–80PubMed
5.
go back to reference Leunig M, Hertel R (1996) Thermal necrosis after tibial reaming for intramedullary nail fixation. A report of three cases. J Bone Joint Surg Br 78(4):584–587PubMed Leunig M, Hertel R (1996) Thermal necrosis after tibial reaming for intramedullary nail fixation. A report of three cases. J Bone Joint Surg Br 78(4):584–587PubMed
6.
go back to reference Brisman DL (1996) The effect of speed, pressure, and time on bone temperature during the drilling of implant sites. Int J Oral Maxillofac Implants 11(1):35–37PubMed Brisman DL (1996) The effect of speed, pressure, and time on bone temperature during the drilling of implant sites. Int J Oral Maxillofac Implants 11(1):35–37PubMed
7.
go back to reference Kerawala CJ, Martin IC, Allan W, Williams ED (1999) The effects of operator technique and bur design on temperature during osseous preparation for osteosynthesis self-tapping screws. Oral Surg Oral Med Oral Pathol Oral Radiol Endod 88(2):145–150PubMedCrossRef Kerawala CJ, Martin IC, Allan W, Williams ED (1999) The effects of operator technique and bur design on temperature during osseous preparation for osteosynthesis self-tapping screws. Oral Surg Oral Med Oral Pathol Oral Radiol Endod 88(2):145–150PubMedCrossRef
8.
go back to reference Harris BH, Kohles SS (2001) Effects of mechanical and thermal fatigue on dental drill performance. Int J Oral Maxillofac Implants 16:819–826PubMed Harris BH, Kohles SS (2001) Effects of mechanical and thermal fatigue on dental drill performance. Int J Oral Maxillofac Implants 16:819–826PubMed
9.
go back to reference Oliveira N, Alaejos-Algarra F, Mareque-Bueno J, Ferres-Padro E, Hernandez-Alfaro F (2012) Thermal changes and drill wear in bovine bone during implant site preparation. A comparative in vitro study: twisted stainless steel and ceramic drills. Clin Oral Implants Res 23(8):963–969PubMedCrossRef Oliveira N, Alaejos-Algarra F, Mareque-Bueno J, Ferres-Padro E, Hernandez-Alfaro F (2012) Thermal changes and drill wear in bovine bone during implant site preparation. A comparative in vitro study: twisted stainless steel and ceramic drills. Clin Oral Implants Res 23(8):963–969PubMedCrossRef
10.
go back to reference Sener BC, Dergin G, Gursoy B, Kelesoglu E, Slih I (2009) Effects of irrigation temperature on heat control in vitro at different drilling depths. Clin Oral Implants Res 20:294–298PubMedCrossRef Sener BC, Dergin G, Gursoy B, Kelesoglu E, Slih I (2009) Effects of irrigation temperature on heat control in vitro at different drilling depths. Clin Oral Implants Res 20:294–298PubMedCrossRef
11.
go back to reference Eriksson A, Albrektsson T, Grane B, McQueen D (1982) Thermal injury to bone. A vital-microscopic description of heat effects. Int J Oral Surg 11(2):115–121PubMedCrossRef Eriksson A, Albrektsson T, Grane B, McQueen D (1982) Thermal injury to bone. A vital-microscopic description of heat effects. Int J Oral Surg 11(2):115–121PubMedCrossRef
12.
go back to reference Eriksson RA, Albrektsson T, Magnusson B (1984) Assessment of bone viability after heat trauma. A histological, histochemical and vital microscopic study in the rabbit. Scand J Plast Reconstr Surg 18:261–268PubMedCrossRef Eriksson RA, Albrektsson T, Magnusson B (1984) Assessment of bone viability after heat trauma. A histological, histochemical and vital microscopic study in the rabbit. Scand J Plast Reconstr Surg 18:261–268PubMedCrossRef
13.
go back to reference Hillery MT, Shuaib I (1999) Temperature effects in the drilling of human and bovine bone. J Mat Proc Technology 92–93:302–308CrossRef Hillery MT, Shuaib I (1999) Temperature effects in the drilling of human and bovine bone. J Mat Proc Technology 92–93:302–308CrossRef
14.
go back to reference Eriksson AR, Albrektsson T (1983) Temperature threshold levels for heat-induced bone tissue injury: a vital-microscopic study in the rabbit. J Prosthet Dent 50:101–107PubMedCrossRef Eriksson AR, Albrektsson T (1983) Temperature threshold levels for heat-induced bone tissue injury: a vital-microscopic study in the rabbit. J Prosthet Dent 50:101–107PubMedCrossRef
15.
go back to reference Eriksson RA, Adell R (1986) Temperatures during drilling for the placement of implants using the osseointegration technique. J Oral Maxillofac Surg 44(1):4–7PubMedCrossRef Eriksson RA, Adell R (1986) Temperatures during drilling for the placement of implants using the osseointegration technique. J Oral Maxillofac Surg 44(1):4–7PubMedCrossRef
17.
go back to reference Sharawy M, Misch CE, Weller N, Tehemar S (2002) Heat generation during implant drilling: the significance of motor speed. J Oral Maxillofac Surg 60(10):1160–1169PubMedCrossRef Sharawy M, Misch CE, Weller N, Tehemar S (2002) Heat generation during implant drilling: the significance of motor speed. J Oral Maxillofac Surg 60(10):1160–1169PubMedCrossRef
18.
go back to reference Ercoli C, Funkenbusch PD, Lee HJ, Moss ME, Graser GN (2004) The influence of drill wear on cutting efficiency and heat production during osteotomy preparation for dental implants: a study of drill durability. Int J Oral Maxillofac Implants 19(3):335–349PubMed Ercoli C, Funkenbusch PD, Lee HJ, Moss ME, Graser GN (2004) The influence of drill wear on cutting efficiency and heat production during osteotomy preparation for dental implants: a study of drill durability. Int J Oral Maxillofac Implants 19(3):335–349PubMed
19.
go back to reference Benington IC, Biagioni PA, Briggs J, Sheridan S, Lamey PJ (2002) Thermal changes observed at implant sites during internal and external irrigation. Clin Oral Implants Res 13:293–297PubMedCrossRef Benington IC, Biagioni PA, Briggs J, Sheridan S, Lamey PJ (2002) Thermal changes observed at implant sites during internal and external irrigation. Clin Oral Implants Res 13:293–297PubMedCrossRef
20.
go back to reference Augustin G, Davila S, Udiljak T, Vedrina DS, Bagatin D (2009) Determination of spatial distribution of increase in bone temperature during drilling by infrared thermography: preliminary report. Arch Orthop Trauma Surg 129(5):703–709PubMedCrossRef Augustin G, Davila S, Udiljak T, Vedrina DS, Bagatin D (2009) Determination of spatial distribution of increase in bone temperature during drilling by infrared thermography: preliminary report. Arch Orthop Trauma Surg 129(5):703–709PubMedCrossRef
21.
go back to reference Lavelle C, Wedgwood D (1980) Effect of internal irrigation on frictional heat generated from bone drilling. J Oral Surg 38(7):499–503PubMed Lavelle C, Wedgwood D (1980) Effect of internal irrigation on frictional heat generated from bone drilling. J Oral Surg 38(7):499–503PubMed
22.
go back to reference Misir AF, Sumer M, Yenisey M, Ergioglu E (2009) Effect of surgical drill guide on heat generated from implant drilling. J Oral Maxillofac Surg 67(12):2663–2668PubMedCrossRef Misir AF, Sumer M, Yenisey M, Ergioglu E (2009) Effect of surgical drill guide on heat generated from implant drilling. J Oral Maxillofac Surg 67(12):2663–2668PubMedCrossRef
23.
go back to reference Abouzgia MB, Symington JM (1996) Effect of drill speed on bone temperature. Int J Oral Maxillofac Surg 25(5):394–399PubMedCrossRef Abouzgia MB, Symington JM (1996) Effect of drill speed on bone temperature. Int J Oral Maxillofac Surg 25(5):394–399PubMedCrossRef
24.
go back to reference Gehrke SA, Neto HL, Mardegan FE (2013) Investigation of the effect of movement and irrigation systems on temperature in the conventional drilling of cortical bone. Br J Oral Maxillofac Surg S0266–4356(13):00004–1. doi:10.1016/j.bjoms.2012.10.023 Gehrke SA, Neto HL, Mardegan FE (2013) Investigation of the effect of movement and irrigation systems on temperature in the conventional drilling of cortical bone. Br J Oral Maxillofac Surg S0266–4356(13):00004–1. doi:10.​1016/​j.​bjoms.​2012.​10.​023
25.
go back to reference Saha S, Pal S, Albright JA (1982) Surgical drilling: design and performance of an improved drill. J Biomech Eng 104:245–252PubMedCrossRef Saha S, Pal S, Albright JA (1982) Surgical drilling: design and performance of an improved drill. J Biomech Eng 104:245–252PubMedCrossRef
26.
go back to reference Augustin G, Zigman T, Davila S, Udilljak T, Staroveski T, Brezak D et al (2012) Cortical bone drilling and thermal osteonecrosis. Clin Biomech (Bristol, Avon) 27(4):313–325CrossRef Augustin G, Zigman T, Davila S, Udilljak T, Staroveski T, Brezak D et al (2012) Cortical bone drilling and thermal osteonecrosis. Clin Biomech (Bristol, Avon) 27(4):313–325CrossRef
27.
go back to reference Oh HJ, Wikesjo UM, Kang HS, Ku Y, Eom TG, Koo KT (2011) Effect of implant drill characteristics on heat generation in osteotomy sites: a pilot study. Clin Oral Implants Res 22(7):722–726PubMedCrossRef Oh HJ, Wikesjo UM, Kang HS, Ku Y, Eom TG, Koo KT (2011) Effect of implant drill characteristics on heat generation in osteotomy sites: a pilot study. Clin Oral Implants Res 22(7):722–726PubMedCrossRef
28.
go back to reference Benington IC, Biagioni PA, Crossey PJ, Hussey DL, Sheridan S, Lamey PJ (1996) Temperature changes in bovine mandibular bone during implant site preparation: an assessment using infra-red thermography. J Dent 24(4):263–267PubMedCrossRef Benington IC, Biagioni PA, Crossey PJ, Hussey DL, Sheridan S, Lamey PJ (1996) Temperature changes in bovine mandibular bone during implant site preparation: an assessment using infra-red thermography. J Dent 24(4):263–267PubMedCrossRef
29.
go back to reference Chacon GE, Bower DL, Larsen PE, McGlumphy EA, Beck FM (2006) Heat production by 3 implant drill systems after repeated drilling and sterilization. J Oral Maxillofac Surg 64(2):265–269PubMedCrossRef Chacon GE, Bower DL, Larsen PE, McGlumphy EA, Beck FM (2006) Heat production by 3 implant drill systems after repeated drilling and sterilization. J Oral Maxillofac Surg 64(2):265–269PubMedCrossRef
30.
go back to reference Yacker MJ, Klein M (1996) The effect of irrigation on osteotomy depth and bur diameter. Int J Oral Maxillofac Implants 11:634–638PubMed Yacker MJ, Klein M (1996) The effect of irrigation on osteotomy depth and bur diameter. Int J Oral Maxillofac Implants 11:634–638PubMed
31.
go back to reference Jochum RM, Reichart PA (2000) Influence of multiple use of Timedur-titanium cannon drills: thermal response and scanning electron microscopic findings. Clin Oral Implants Res 11:139–143PubMedCrossRef Jochum RM, Reichart PA (2000) Influence of multiple use of Timedur-titanium cannon drills: thermal response and scanning electron microscopic findings. Clin Oral Implants Res 11:139–143PubMedCrossRef
32.
go back to reference Carvalho AC, Queiroz TP, Okamoto R, Margonar R, Garcia IR Jr, Magro Filho O (2011) Evaluation of bone heating, immediate bone cell viability, and wear of high-resistance drills after the creation of implant osteotomies in rabbit tibias. Int J Oral Maxillofac Implants 26(6):1193–1201PubMed Carvalho AC, Queiroz TP, Okamoto R, Margonar R, Garcia IR Jr, Magro Filho O (2011) Evaluation of bone heating, immediate bone cell viability, and wear of high-resistance drills after the creation of implant osteotomies in rabbit tibias. Int J Oral Maxillofac Implants 26(6):1193–1201PubMed
33.
go back to reference Augustin G, Davila S, Udilljak T, Staroveski T, Brezak D, Babic S (2012) Temperature changes during cortical bone drilling with a newly designed step drill and an internally cooled drill. Int Orthop 36(7):1449–1456PubMedCentralPubMedCrossRef Augustin G, Davila S, Udilljak T, Staroveski T, Brezak D, Babic S (2012) Temperature changes during cortical bone drilling with a newly designed step drill and an internally cooled drill. Int Orthop 36(7):1449–1456PubMedCentralPubMedCrossRef
34.
go back to reference Watanabe F, Tawada Y, Komatsu S, Hata Y (1992) Heat distribution in bone during preparation of implant sites: heat analysis by real-time thermography. Int J Oral Maxillofac Implants 7(2):212–219PubMed Watanabe F, Tawada Y, Komatsu S, Hata Y (1992) Heat distribution in bone during preparation of implant sites: heat analysis by real-time thermography. Int J Oral Maxillofac Implants 7(2):212–219PubMed
35.
go back to reference Cordioli G, Majzoub Z (1997) Heat generation during implant site preparation: an in vitro study. Int J Oral Maxillofac Implants 12:186–193PubMed Cordioli G, Majzoub Z (1997) Heat generation during implant site preparation: an in vitro study. Int J Oral Maxillofac Implants 12:186–193PubMed
36.
go back to reference Iyer S, Weiss C, Mehta A (1997) Effects of drill speed on heat production and the rate and quality of bone formation in dental implant osteotomies. Part I: relationship between drill speed and heat production. Int J Prosthodont 10:411–414PubMed Iyer S, Weiss C, Mehta A (1997) Effects of drill speed on heat production and the rate and quality of bone formation in dental implant osteotomies. Part I: relationship between drill speed and heat production. Int J Prosthodont 10:411–414PubMed
37.
go back to reference Scarano A, Piattelli A, Assenza B, Carinci F, Di Donato L, Romani GL et al (2011) Infrared thermographic evaluation of temperature modifications induced during implant site preparation with cylindrical versus conical drills. Clin Implant Dent Relat Res 13(4):319–323PubMedCrossRef Scarano A, Piattelli A, Assenza B, Carinci F, Di Donato L, Romani GL et al (2011) Infrared thermographic evaluation of temperature modifications induced during implant site preparation with cylindrical versus conical drills. Clin Implant Dent Relat Res 13(4):319–323PubMedCrossRef
38.
go back to reference Wachter R, Stoll P (1991) Increase of temperature during osteotomy. In vitro and in vivo investigations. Int J Oral Maxillofac Surg 20(4):245–249PubMedCrossRef Wachter R, Stoll P (1991) Increase of temperature during osteotomy. In vitro and in vivo investigations. Int J Oral Maxillofac Surg 20(4):245–249PubMedCrossRef
Metadata
Title
Study of temperature variation in cortical bone during osteotomies with trephine drills
Authors
Sergio Alexandre Gehrke
Marcelo Khoury Pazetto
Sérgio de Oliveira
Stefano Corbella
Silvio Taschieri
Fábio E. C. Mardegan
Publication date
01-09-2014
Publisher
Springer Berlin Heidelberg
Published in
Clinical Oral Investigations / Issue 7/2014
Print ISSN: 1432-6981
Electronic ISSN: 1436-3771
DOI
https://doi.org/10.1007/s00784-013-1163-4

Other articles of this Issue 7/2014

Clinical Oral Investigations 7/2014 Go to the issue