Top

Published in:

01-11-2010 | Original Article

Effect of acid etching duration on tensile bond strength of composite resin bonded to erbium:yttrium–aluminium–garnet laser-prepared dentine. Preliminary study

Authors: M. Chousterman, D. Heysselaer, S. M. Dridi, F. Bayet, B. Misset, L. Lamard, A. Peremans, C. Nyssen-Behets, S. Nammour

Published in: Lasers in Medical Science | Issue 6/2010

Abstract

The purpose of this study was to compare the tensile bond strength of composite resin bonded to erbium:yttrium–aluminium–garnet (Er:YAG) laser-prepared dentine after different durations of acid etching. The occlusal third of 68 human third molars was removed in order to expose the dentine surface. The teeth were randomly divided into five groups: group B (control group), prepared with bur and total etch system with 15 s acid etching [37% orthophosphoric acid (H₃PO₄)]; group L15, laser photo-ablated dentine (200 mJ) (laser irradiation conditions: pulse duration 100 µs, air–water spray, fluence 31.45 J/ cm², 10 Hz, non-contact hand pieces, beam spot size 0.9 mm, irradiation speed 3 mm/s, and total irradiation time 2 x 40 s); group L30, laser prepared, laser conditioned and 30 s acid etching; group L60, laser prepared, laser conditioned and 60 s acid etching; group L90, laser prepared, laser conditioned and 90 s acid etching. A plot of composite resin was bonded onto each exposed dentine and then tested for tensile bond strength. The values obtained were statistically analysed by analysis of variance (ANOVA) coupled with the Tukey–Kramer test at the 95 % level. A 90 s acid etching before bonding showed the best bonding value (P < 0.05) when compared with all the other groups including the control group. There is no significance difference between other groups, nor within each group and the control group. There was a significant increase in tensile bond strength of the samples acid etched for 90 s.

Hibst R, Keller U (1989) Experimental studies of the application of the Er:YAG laser on dental hard structures: (I) Measurement of the ablation rate. Laser Surg Med 9:338–344CrossRef

Mehl A, Kremers L, Salzmann K, Hickel R (1997) 3D volume-ablation rate and thermal side effects with the Er:YAG and Nd:YAG laser. Dent Mater 13:246–251CrossRefPubMed

Keller U, Hibst R (1989) Experimental studies of the application of the Er:YAG laser on dental hard structures: (II) Light microscopic and SEM investigations. Laser Surg Med 9:345–351CrossRef

Visuri SR, Gilbert JL, Wright DD, Wigdor HA, Walsh JT Jr (1996) Shear strength of composite bonded to Er:YAG laser-prepared dentin. J Dent Res 75:599–605CrossRefPubMed

Trajtenberg CP, Pereira PN, Powers JM (2004) Resin bond strength and micromorphology of human teeth prepared with erbium:YAG laser. Am J Dent 17:331–336PubMed

Dunn WJ, Davis JT, Bush AC (2005) Shear bond strength and SEM evaluation of composite bonded to Er:YAG laser-prepared dentin and enamel. Dent Mater 21:616–624CrossRefPubMed

Bertrand MF, Hessleyer D, Muller-Bolla M, Nammour S, Rocca JP (2004) Scanning electron microscopic evaluation of resin-dentin interface after Er:YAG laser preparation. Laser Surg Med 35:51–57CrossRef

Esteves-Oliveira M, Zezeli DM, Appel C, Turbino ML, Aranha ACC, de Paula Eduardo C, Gutknecht N (2007) Bond strength of self-etching primer to bur cut, Er, Cr:YSGG, and Er:YAG lased dental surfaces. Photomed Laser Surg 25:373–380CrossRefPubMed

Brulat N, Rocca JP, Leforestier E, Fiorucci G, Nammour S, Bertrand MF. (2009) Shear bond strength of self-etching adhesive systems to Er:YAG-laser-prepared dentin. Lasers Med Sci 24:53–57

10.

Gurgan S, Kiremitci A, Cakir FY, Gorucu J, Alpaslan T, Yazici E, Gutknecht N (2008) Shear bond strength of composite bonded to Er, Cr:YSGG laser-prepared dentin. Photomed Laser Surg 26:495–500CrossRefPubMed

11.

Omae M, Inoue M, Itota T, Finger WJ, Inoue M, Tanaka K, Yamamoto K, Yoshiyama M (2007) Effect of a desensitizing agent containing glutaraldehyde and HEMA on bond strength to Er:YAG laser-irradiated dentine. J Dent 35:398–402CrossRefPubMed

12.

Aoki A, Ishikawa I, Yamada T, Otsuki M, Watanabe H, Tagami J, Ando Y, Yamamoto H (1998) Comparison between Er:YAG laser and conventional technique for root caries treatment in vitro. J Dent Res 77:1404–1414CrossRefPubMed

13.

Ceballos L, Osorio R, Toledano M, Marshall GW (2001) Microleakage of composite restorations after acid or Er:YAG laser cavity treatment. Dent Mater 17:340–346CrossRefPubMed

14.

Ceballos L, Toledano M, Osorio R, Tay FR, Marshall GW (2002) Bonding to Er-YAG-laser-treated dentin. J Dent Res 81:119–122CrossRef

15.

Proceedings of the 1st International Workshop of Evidence Based Dentistry on Lasers in Dentistry, 2007, Quintessence, Germany

16.

Delmé KI, De Moor RJ (2007) Scanning electron microscopic evaluation of enamel and dentin surface after Er:YAG laser preparation and laser conditioning. Photomed Laser Surg 25:393–401CrossRefPubMed

17.

De Carvalho RCR, De Freitas PM, Otsuki M, de Paula Eduardo C, Tagami J (2008) Micro-shear bond strength of Er:YAG-laser-treated dentin. Lasers Med Sci 23:117–124CrossRefPubMed

18.

Giachetti L, Russo DS, Scarpelli F, Vitale M (2004) SEM analysis of dentin treated with the Er:YAG laser: a pilot study of the consequences resulting from laser use on adhesion mechanism. J Clin Laser Med Surg 22:35–41CrossRefPubMed

19.

Camerlingo C, Lepore M, Gaeta GM, Riccio R, Riccio C, De Rosa A, De Rosa M (2004) Er:YAG laser treatments on dentine surface: micro-Raman spectroscopy and SEM analysis. J Dent 32:399–405CrossRefPubMed

20.

Silva Soares LE, Resende EBPS, Brugnera A Jr, Zanin FAA, Martin AA (2007) Combined FT-Raman and SEM studies of the effects of Er:YAG laser irradiation on dentin. Photomed laser Surg 25:239–244CrossRef

21.

Delmé KI, Cardoso MV, Mine A, De Moor RJ, Van Meerbeek B (2009) Transmission electron microscopic examination of the interface between a resin-modified glass-ionomer and Er:YAG laser-irradiated dentin. Photomed Laser Surg 27:317–323CrossRefPubMed

22.

He Z, Otsuki M, Sadr A, Tagami J. (2009) Acid resistance of dentin after erbium: yttrium-aluminum-garnet laser irradiation. Lasers Med Sci 24:507–513

Title: Effect of acid etching duration on tensile bond strength of composite resin bonded to erbium:yttrium–aluminium–garnet laser-prepared dentine. Preliminary study
Authors: M. Chousterman
D. Heysselaer
S. M. Dridi
F. Bayet
B. Misset
L. Lamard
A. Peremans
C. Nyssen-Behets
S. Nammour
Publication date: 01-11-2010
Publisher: Springer-Verlag
Published in: Lasers in Medical Science / Issue 6/2010
Print ISSN: 0268-8921
Electronic ISSN: 1435-604X
DOI: https://doi.org/10.1007/s10103-009-0719-7

Keynote webinar | Spotlight on medication adherence

Springer Medicine

Effect of acid etching duration on tensile bond strength of composite resin bonded to erbium:yttrium–aluminium–garnet laser-prepared dentine. Preliminary study

Abstract

Keynote webinar | Spotlight on medication adherence

Springer Medicine

Abstract

Please log in to get access to this content

Other articles of this Issue 6/2010

In vitro evaluation of microleakage under orthodontic brackets using two different laser etching, self etching and acid etching methods

Laser phototherapy in the treatment of periodontal disease. A review

Bactericidal activity of erbium, chromium:yttrium–scandium–gallium–garnet laser in root canals

Evaluation of mechanical properties and porcelain bonded strength of nickel–chromium dental alloy fabricated by laser rapid forming

The heat-pipe resembling action of boiling bubbles in endovenous laser ablation

Evaluation of the furcation area permeability of deciduous molars treated by neodymium:yttrium–aluminum–garnet laser or adhesive