Abstract
This paper presents novel micropumps that are actuated by hydrogel drying. Gel dehydration by evaporation makes the gel absorbent. This results in the suction of the liquid from the connected microchannel into the gel. Therefore, the liquid sample flows through the microchannel as a result of this negative pressure. Micropumps with simple structures were fabricated using microfabrication techniques with glass, silicone polymer, and agarose or polyacrylamide gel. The average volume flow rate was measured in variations of several to several tens of picoliters per second according to the kind of gel. This gel micropump functioned for several hours without severe flow rate fluctuations. This pump was also able to deliver viscous fluids such as blood. This pump would be useful for microchips that need slow but steady and long-lasting actuation in the addition of sampling proteins from viscous liquids such as blood. Theoretical approach about diffusion movement of liquid into the gel was also described.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Nguyen, N.-T., Huang, X. & Chuan, T.K. MEMS-micropumps: a review. J. Fluid. Eng.-T. ASME 124, 384–392 (2002).
Harmon, M.E., Tang, M. & Frank, C.W. A microfluidic actuator based on thermoresponsive hydrogels. Polymer 44, 4547–4556 (2003).
Eddington, D.T. & Beebe, D.J. A valved responsive hydrogel microdispensing device with integrated pressure source. J. Microelectromech. Syst. 13, 586–593 (2004).
Beebe, D.J. et al. Functional hydrogel structures for autonomous flow control inside microfluidic channels. Nature 404, 588–590 (2000).
Liu, R.H., Yu, Q. & Beebe, D.J. Fabrication and characterization of hydrogel-based microvalves. J. Microelectromech. Syst. 11, 45–53 (2002).
Park, J.Y., Oh, H.J., Kim, D.J., Baek, J.Y. & Lee, S.H. A polymeric microfluidic valve employing a pH-responsive hydrogel microsphere as an actuating source. J. Micromech. Microeng. 16, 656–663 (2006).
Richter, A., Kuckling, D., Howitz, S., Gehring, T. & Arndt, K.-F. Electronically controllable microvalves based on smart hydrogels: magnitudes and potential applications. J. Microelectromech. Syst. 12, 748–753 (2003).
Mao, L. et al. Structure and character of artificial muscle model constructed from fibrous hydrogel. Curr. Appl. Phys. 5, 426–428 (2005).
Sambrook, J. & Russell, D.W. Molecular Cloning; A Laboratory Manual (third ed.). New York: Cold Spring Harbor Laboratory Press (2001).
Choi, Y.H. & Lee, S.S. Novel micropump actuated by drying of gel. Proc. Micro Total Analysis Systems, Squaw Valley, California, USA, 219–222 (2003).
Zimmermann, M., Bentley, S., Schmid, H., Hunziker, P. & Delamarche, E. Continuous flow in open microfluidics using controlled evaporation. Lab Chip 5, 1355–1359 (2005).
Good, B.T., Bowman, C.N. & Davis, R.H. A wateractivated pump for portable microfluidic applications. J. Colloid Interf. Sci. 305, 239–249 (2007).
Nield, D.A. Convection in Porous Media (third ed.). New York: Springer (2006).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Choi, Y.H., Lee, S.S. & Chung, K.H. Microfluidic actuation and sampling by dehydration of hydrogel. BioChip J 4, 63–69 (2010). https://doi.org/10.1007/s13206-010-4110-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13206-010-4110-3